Research Activities

My research interests include passive (or semi-passive) transponders which can not be modeled as linear time-invariant systems. These transponders have enhanced performance in term of coding capacity and read range compared to classical linear time-invariant systems and can only be achieved be breaking the linearity or the time invariance associated to the transponder .

Introduction

Fig. 1: Environment under white light

Fig. 2: Environment under red light

Almost all the objects that we can see or characterize are Linear Time Invariant (LTI) systems. It implies that if they are impinged by an electromagnetic wave at a frequency $f_{0}$ (in input), they also reflect or backscatter an electromagnetic wave at the same frequency $f_{0}$ (in output).

These LTI systems can be fully characterized by their impulse response $h(t)$ in the time domain or their transfer function $H(f)$ in the frequency domain. The output signal $y(t)$ can be obtained in the time domain if the input signal $x(t)$ is known as:

$y(t)=x(t)*h(t)$

Expression can also be derived in the frequency domain:

$Y(f)=X(f)\times H(f)$

Classical examples include dynamical systems (electrical circuits, mechanical systems...). If we consider that the incident waveform is a continuous wave of frequency $f_{0}$ then its real signal can be expressed as $x(t)=\cos 2\pi f_{0}t$. The received signal takes in that case, the simple form:

$y(t)=|H(f_{0})|\cos(2\pi f_{0}t+Arg(H(f_{0})))$

where we can easily see that the backscattered signal of a LTI system can only affect the amplitude $|H(f_{0})|$ and/or the phase $Arg(H(f_{0}))$ of the incident waveform. Note that all the received power is also located at $f_{0}$ since a LTI system can not generate a frequency which is not in the input signal.

Let's consider a simple example, where an environment composed of different pens on a white support is illuminated by white light as in Fig. 1. Under these conditions, note that each object is characterized by a different color since they all accept the incident power and they each reflect a tiny part of the input spectrum. However, if we replace the white light by a red light (or any monochromatic color), each object will reflect the CW with an attenuation $|H(f_{0})|$ and a phase shift of $Arg(H(f_{0}))$ but the frequency of the reflected wave will remain at $f_{0}$ and the color of all object lies in between red (when attenuation is low) and black (when attenuation is high). Results are presented in Fig. 2. Almost all the objects that we see around us (like these pens and this support) are LTI systems.

This simple observation implies important constraints if we want to identify object according the their backscattered or reflected signal:

1. The coding capacity only depends on the number of the color which can be distinguished. This capacity is only a function of the frequency resolution compared to the total bandwidth used by the reader. The total bandwidth used by the reader depends on the input signal. That is why we can differentiate pen under white light and not under red light.
2. The associated read range is only limited by the ratio in between the power backscattered by the object compared to the power reflected by the environment at the same frequency. This condition is harder to see with the picture since, pens can be separated spatially due to the camera lens but remember that an antenna cannot detect the direction of arrival of the received power.

These limitation only appear since both pens and support (white table) are LTI systems.

Research Interest

My research interests include all systems which cannot be modeled by a linear time-invariant system. As a direct consequence, these systems cannot be described by an impulse response or a transfer function and are able to accept the incident power at a given frequency and reflect or backscatter (a part of) this power at an other frequency or in another bandwidth. For example, in Fig. 2, these systems could appear under the red illumination as blue of green objects... This result can be obtained by only 2 ways, breaking the linearity (i.e., non linear systems) or breaking the time invariance (i.e. linear time variant systems). A third method consist of breaking the invariance on the reader side.

Non linear systems

Transponders based on a non-linear element (such as a Schottky diode) can accept a power at $f_{0}$ and generate a power at $nf_{0}$. Let's consider the simple circuit composed of a generator connected to a load but where a diode in inserted in serial in the circuit. The diode is a simple device which conducts the current mainly in a single direction. The relation which describe the current $I$ flowing through the diode as a function of the voltage across the junction $V_{D}$ can be expressed as:

$I=I_{S}\left(e^{\frac {V_{D}}{nV_{T}}}-1\right)$

with $V_{T}=kT/q$. If we consider a small variation of the junction voltage $v$ around a bias voltage operating point $V_{b}$, the current $i$ can be expressed as Taylor series:

$i(v)=i(V_{b})+{\frac {i^{(1)}}{1!}}(v-V_{b})+{\frac {i^{(2)}(V_{b})}{2!}}(v-V_{D})^{2}+{\frac {i^{(3)}(V_{b})}{3!}}(v-V_{b})^{3}+\cdots$

where $i^{(n)}$ is the $n^{\text{th}}$-derivative of $i(v)$ according to $v$.

If an harmonic tension such as $v(t)=A\cos \omega _{0}t$ is applied to this diode, its current $i(t)$ can be expressed as:

${\begin{aligned}i(V_{D},t)&=i(V_{D})+[{\frac {A^{2}}{4}}i^{(2)}(V_{b})+{\frac {A^{4}}{64}}i^{(4)}(V_{b})+\cdots ]\\&+[Ai^{(1)}(V_{D})+{\frac {A^{3}}{8}}i^{(3)}(V_{b})+\cdots ]\cos \omega _{0}t\\&+[{\frac {A^{2}}{4}}i^{(2)}(V_{b})+{\frac {A^{4}}{48}}i^{(4)}(V_{b})+\cdots ]\cos 2\omega _{0}t\\&+[{\frac {A^{3}}{24}}i^{(3)}(V_{b})+{\frac {A^{5}}{384}}i^{(4)}(V_{b})+\cdots ]\cos 3\omega _{0}t\\&+\cdots \end{aligned}}$

where we can see that an infinite sum of harmonics has been created due the non-linear behavior of the diode.

Fig. 3: Voltage across R in the frequency domain

The circuit has been simulated using ngspice using the transient analysis to clearly see the effect of the non-linearity of a HSMS285x diode. Amplitude has been set to 1V, frequency at 915 MHz. Simulation has been computed over a duration of 10 periods with 100 samples per period. Fourier series have been computed over the voltage across the load.

.title diode
.param A = 1
.param f0 = 915e6
.model hsms285x D (IS=3e-6 RS=25 N=1.06 CJO=0.18pF VJ=0.35 M=0.5 EG=0.69 XTI=2 BV=3.8 IBV=3e-4)
V1 1 0 dc 0 SIN(0 A f0 0NS 0)
Ra 2 1 50
D1 2 3 hsms285x
Rl 3 0 50
.end

.csparam csf0 = {f0}
.csparam duration = {10.0/f0}
.csparam fsample = {1/(100*f0)}
.control
  tran $&fsample $&duration
  plot v(3)
  fourier $&csf0 v(3)
.endc

The simulation clearly shows that the power dissipated into the load contains power at $f_{0}$ but also at $nf_{0}$ due to the non-linear behavior of the diode.

For passive harmonic transponders, an antenna accepting the power at $f_{0}$ have to be added. The backscattered power at $nf_{0}$ should also be re-radiated by another antenna. The main difficulty appears from the incident power which is very low (few micro Watt) which need to generate a voltage higher than the threshold of the diode (around 0.3 V). Usually the conversion loss associated to these devices is lower than -20 dB (i.e. only 1% of the incident power is converted to another frequency). However, read range of these transponders can easily achieve more than 5 m while satisfying regulation standards.

Linear time variant systems

Fig. 4: PSD of the signal backscattered by a modulating tag.

These class of transponders include many examples. The more famous ones are classical RFID tags. UHF RFID tags can, when a sufficient power is received by the chip, switch the internal load connected to the antenna in between 2 values, its RCS is also modified and becomes a function of the time. Finally the variations of the backscattered signal generate a modulation which can be detected by the reader. As a direct consequence, the backscattered power spectral density includes components which are not at $f_{0}$. If the transmission data rate is much lower than the carrier frequency, narrow band signal approximation holds and PSD is located around $f_{0}$. The exact characteristics of the PSD depends on the data encoding used by the tag during the communication. The UHF RFID standard defines two different modulations for the tag which are FM0 and Miller (with different subcarrier sequences). Analytical formula of the PSD for FM0 is known and is equal to the Manchester encoding. For Miller modulation, analytical formula is also known, but without considering the subcarrier sequences. Fig. 5 presents the PSD of the baseband signals corresponding to the different modulations used by the tag. For all modulation we can see that the PSD is spread around $f_{0}$ and that the system can not be considered as a LTI system.

Another example appears when objects are moved or rotated into space. This interesting phenomenon is better illustrated by considering the simple case where a target is impinged by a continuous wave at a frequency $f_{0}$, if the radial speed of the target compared to the antenna is not zero, Doppler effect actually modifies the backscattered wave frequency received by the antenna which can be expressed as:

$f=\left({\frac {c}{c\pm v_{s}}}\right)f_{0}$

Fig. 5: Spectrum of a rotating dipole impinged by a CW.

Periodical movements of frequency $f_{r}$, such as vibrations and rotations, lead to simple analytical expressions where the backscattered spectrum is composed of discrete peaks located at $f_{0}\pm nf_{r}$. Let's consider a vertical dipole oriented along $z$ located at $x=5$ cm and $y=0$ cm and impinged by a plane wave at 915 MHz propagating along $y$. If we rotate this dipole along the $z$ axis with a frequency $f_{r}$, the phase backscattered electric field in farfield is modulated by a sinus function while the magnitude remains constant (micro-Doppler). This situation can easily by simulated with nec2:

CE MICRO-DOPPLER
GW 0 50 -0.0165 0.05 0. 0.0165 0.05 0. 0.0005
GM 0 0 0. 0. 0. 0. 0. 0.
GE
EX 1 1 1 0 0 0 0 0 0 0
FR 0 1 0 0 915e6 0
RP 0 1 1 1000 0 0 0 0 1
EN

By changing the GM card, the backscattered signal can be determined for all $\theta$ values. Fourier series of this signal can be computed and lead to a discrete spectrum at $kf_{r}$ presented in Fig. 4. Analytical form is identical to a frequency modulated signal with an index modulation of $\beta =1.92$ and can be expressed as a function of the Bessel function of first kind.

Finally, note that for every modification of the response of the transponder during the interrogation done by the reader implies a modulation of the backscattered signal in time which generate a non-zero power in the PSD around $f_{0}$. However these modifications require an energy source which can be brought by the reader itself (as in UHF RFID) or by an external action (as the displacement or rotation of the tag). In these latter case, transponders can be considered as semi-passive.

Imaging systems

Fig. 6: Barcode and modulated reflected signal

Imaging systems are a special kind of linear time variant system where the variations are not produced by the tag but by the reader itself. In this case, the tag remains a LTI systems, but the reading method done by the reader allows to extract the tag response as a function of variation in time which break the invariance propertie. These tags (and the associated reading method) are not limited by the bounds on coding capacity and read range. The simplest example is the barcode and is presented in Fig. 5. Classical barcodes are composed of black stripes and can encode 43 bits of information. Barcodes are read by sweeping the beam produced by a laser diode along the tag and by measuring the variations of the reflected signal in time. Note that this reflected signal is a modulated signal as in the case of UHF RFID and moving or rotating tags. As such, barcodes and their reading method cannot be considered as LTI systems and are characterized by a non-zero delta RCS.

This spatial diversity allows to use the same color multiple time to encode information (stripes do not have to use a different color and 2 colors are enought) which significantly increases the coding capacity. 2D images and their associated reading method can also be considered as linear time variant systems (which include QR code, or any image obtained with a lens and camera sensor). All these systems operate in the optical domain since spatial resolution is only limited by the small beam divergence of laser diodes (less than 1 mrad) or the sensor matrix size of camera sensors. However, note that when frequency is decreased, antenna directivity is also reduced which significantly limits the performance of this approach in the RF domain. For example in UWB band half power angle is usually higher than 10° which imposes large separation in between stripes (or resonators).

Conclusion

I hope you have liked this page. If you have any comment, remarks or questions about these ideas, feel free to send me an email:

nicolas.barbot@lcis.grenoble-inp.fr

Collaborations often start by simple emails...